Tripp Lite SmartPro 230V 1.5kVA 900W Line-Interactive UPS, Tower, LCD, USB, 8 Outlets

OUTPUT Output Volt Amp Capacity (VA) 1500 Output kVA Capacity (kVA) 1.5 Output Watt Capacity (Watts) 900 Nominal Output Voltage(s) Supported 220V; 230V; 240V Nominal Voltage Details 230V nominal output in battery mode Frequency Compatibility 50 / 60 Hz Frequency Compatibility Details Automatic frequency selection Output Voltage Regulation (Line Mode) -18%, 8% Output Voltage Regulation (Battery Mode) /- 5% Output Receptacles (8) C13 Included Output Power Cables Includes 2 C13 to C14 output power cables. Hot-Swap PDU options PDUBHV10 (2U / 8 C13 outlets) Output AC Waveform (AC Mode) Sine wave Output AC Waveform (Battery Mode) PWM sine wave INPUT Rated input current (Maximum Load) 4.4A Nominal Input Voltage(s) Supported 230V AC UPS Input Connection Type C14 inlet UPS Input Connection Description Attached 15cm line cord with C14 inlet. C14 inlet accepts user-supplied AC power cord with country specific plug. Input Circuit Breakers 5.5A UPS Input Cord Length (ft.) 0.5 UPS Input Cord Length (m) 0.2 Input Phase Single-Phase BATTERY Full Load Runtime (min.) 4.5 min. (900w) Half Load Runtime (min.) 12 min. (450w) DC System Voltage (VDC) 24 Battery Recharge Rate (Included Batteries) Less than 4.5 hours from 10% to 90% Internal UPS Replacement Battery Cartridge See RBC Selector for replacement battery information Expandable Runtime No VOLTAGE REGULATION Voltage Regulation Description Automatic voltage regulation (AVR) maintains line power operation with an input voltage range of 144 to 282 Overvoltage Correction Input voltages between 245 and 282 are reduced by 12% Undervoltage Correction Input voltages between 177 and 199 are boosted by 14% Severe Undervoltage Correction Input voltages between 144 and 176 are boosted by 30% USER INTERFACE, ALERTS & CONTROLS Front Panel LCD Display Backlighted LCD screen indicates input voltage, 5-bar battery charge level, overload, AVR, on battery and replace battery status; LCD screen rotates for rack/tower viewing Switches 2 Switches control off/on power status and alarm-cancel/self-test operation Alarm Cancel Operation Power-fail alarm can be silenced using alarm-cancel switch; once silenced, alarm will re-sound to indicate low-battery status Audible Alarm Audible alarm indicates power-failure, low-battery and overload status; alarm can be disabled using PowerAlert software LED Indicators Front panel LCD display SURGE / NOISE SUPPRESSION UPS AC Suppression Joule Rating 890 UPS AC Suppression Response Time Instantaneous UPS Dataline Suppression 1 line TEL/DSL (1 in / 1 out); 10/100Base T Ethernet; Coax jacks (1 set) EMI / RFI AC Noise Suppression Yes PHYSICAL Included Mounting Accessory Description Pair of mounting ears enable tower and 2-4 post rackmount installation Installation Form Factors Supported with Included Accessories Tower Primary Form Factor Rackmount UPS Power Module Dimensions (hwd, cm) 8.89 x 43.82 x 26.67 Rack Height (U Spaces) 2 Minimum Required Rack Depth (cm) 32.51 UPS Power Module Weight (kg) 13.34 Shipping Dimensions (hwd / cm) 19.81 x 38.10 x 54.10 Shipping Weight (kg) 15.51 UPS Housing Material ABS Primary UPS Height (mm) 889 Primary UPS Width (mm) 4,382 Primary UPS Depth (mm) 2,667 ENVIRONMENTAL Operating Temperature Range 32 to 104 degrees Fahrenheit / 0 to 40 degrees Celsius Storage Temperature Range 5 to 122 degrees Fahrenheit / -15 to 50 degrees Celsius Relative Humidity 0 to 95%, non-condensing AC Mode BTU / Hr. (Full Load) 128 Battery Mode BTU / Hr. (Full Load) 542 AC Mode Efficiency Rating (100% Load) 96% COMMUNICATIONS Communications Interface USB (HID enabled); DB9 Serial Network Monitoring Port Description Supports detailed monitoring of UPS and site power conditions PowerAlert Software For local monitoring via the UPS’s built-in communication ports, download PowerAlert Local software at http://www.tripplite.com/poweralert Communications Cable USB and DB9 Serial cabling included WatchDog Compatibility Supports Watchdog application, OS and hard-reboot restart options for remote applications LINE / BATTERY TRANSFER Transfer Time 2-4 milliseconds Low Voltage Transfer to Battery Power (Setpoint) 144 High Voltage Transfer to Battery Power (Setpoint) 282 SPECIAL FEATURES Cold Start (Startup in Battery Mode During a Power Failure) Cold-start operation supported Green Energy-Saving Features Greater than 95% efficiency – GREEN UPS